硬孔攻丝用高性能先端丝锥的设计及应用

热后硬孔攻丝螺纹变形量小、尺寸稳定、强度高。该工艺方法对刀具强度要求较高,使用普通高速钢丝锥和螺纹铣刀加工时,普通高速钢丝锥无法承受热后硬孔攻丝所产生的大扭矩而频繁折断,报废率较高,同时螺纹铣刀成本高,不适合大批量生产。针对热后硬孔攻丝工艺复杂、成本高的问题,专门设计了硬孔攻丝用高性能先端丝锥,解决硬孔攻丝难题,并与其他种类丝锥进行了切削力对比。     

A parametric investigation on seat/occupant contact forces and their relationship with initially perceived discomfort using a configurable seat

The present work investigates the contact forces between sitters and seat as well as their correlations with perceived discomfort. Twelve different economy class aeroplane seat configurations were simulated using a multi-adjustable experimental seat by varying seat pan and backrest angles, as well as seat pan compressed surface. Eighteen males and 18 females, selected by their body mass index and stature, tested these configurations for two sitting postures. Perceived discomfort was significantly affected by seat parameters and posture and correlated both with normal force distribution on the seat-pan surface and with normal forces at the lumbar and head supports. Lower discomfort ratings were obtained for more evenly distributed normal forces on the seat pan. Shear force at the seat pan surface was at its lowest when sitters were allowed to self-select their seat-pan angle, supporting that a shear force should be reduced but not zeroed to improve seating comfort.

Practitioner Summary: The effects of seat-pan and backrest angle, anthropometric dimensions and sitting posture on contact forces and perceived discomfort were investigated using a multi-adjustable experimental seat. In addition to preferred seat profile parameters, the present work provides quantitative guidelines on contact force requirement for improving seating comfort.     

Ergonomically based design of tractor control tools

Musculoskeletal injuries are well-known disorders among the agricultural tractor operators. Overexertion is a critical factor which can agitate these injuries. Physical body characteristics should be measured for an ergonomically best-fit-optimal design for the operators. In this study, a designed setup was employed to derive the applied forces by tractor operators on the control tools. The different muscle strengths including leg/foot strength, hand push/pull strength, and torque strength applied by both hands were measured. A comparison was made for the obtained values for different strengths by considering the effects of hand dominance. The obtained data were used to estimate the maximum allowed forces in these tools. In contrast to the previous studies, the minimum allowed actuating forces of the pedals were calculated using reasonable assumptions. These values could provide more comfort and less exhaustion for the tractor operators. The obtained ranges were benchmarked against corresponding recommended values in some standards (ISO, ISIRI, and ASABE family). The results revealed the unsuitability of evaluated standards for a proper design and the excessive overestimation of those recommended values (in some cases more than 3 times). In all of the design procedure, a suitable attention was paid to accommodate it with more than 90% of target population.Relevance to industryA prosperous industry which considers ergonomic factors in the design of agricultural machine workplace can overcome the disorders and generate more comfort. Evaluating more exact mechanical forces can result in a suitable design of workplace.     

轧机两侧刚度差的数字化分析与改善措施

轧机两侧刚度差是轧机功能精度的最重要指标之一，以弹跳方程为基础定量计算了轧机两侧刚度差对轧制稳定性的影响，主要包括调平值、调平值随轧制力的变化以及甩尾3个方面。以此为基础在某热轧线建立了轧机刚度评价体系，对轧机功能精度进行管控。同时，还分析了轧机两侧刚度差的影响因素，并在定量分析的基础上采取了一系列的改善措施，包括衬板、垫片维护、最大压靠轧制力和标定轧制力的调整等，使轧机刚度和轧制稳定性得到大幅提升。     

车辆自组织网络中新型NP-CSMA随机多址协议研究分析

智能交通的出现使得车辆自组织网络受到越来越多的关注。车辆自组织网络的动态拓扑结构变化非常剧烈,这对网络的吞吐率、传输速率等性能提出了很高的要求。提出1种具有握手机制协议的自适应多通道双时钟NP-CSMA随机多址接入协议。该协议首先区分2种P-CSMA协议,握手机制成功解决了隐藏的终端问题,双时钟机制减少了平均空闲时间,多通道机制增加通道数量和划分用户优先级的同时提高了系统吞吐率,自适应机制能够使系统在高负载下保持稳定吞吐率。还对该协议的传输速率进行了分析,得出该协议的传输速率相对较高的结论。通过平均周期方法推导吞吐率和传输速率的计算公式,仿真结果与理论推导一致。     

Thin‐film nanostructure and polymer architecture in semicrystalline syndiotactic poly(p‐methylstyrene)–(cis‐1,4‐polybutadiene) multiblock copolymers

The thin‐film morphology of stereoregular syndiotactic poly(p‐methylstyrene)–(cis‐1,4‐polybutadiene) (sP(pMS–B)) multiblock copolymers has been investigated using tapping mode atomic force microscopy with variation of the polymer composition and monomer block lengths. The morphology of the thin films ranges from isolated circular domains of sP(pMS) embedded into a matrix of polybutadiene (PB) to isolated domains of PB embedded into a matrix of sP(pMS), passing through bicontinuous (jagged) lamellae when the pMS concentration is in the range 20–67 mol%. Multiple folding of the polymer segments, i.e. where reciprocal inclusions of polymer segments to each other phase are able to generate greater domain, has been postulated and validated by considerations on the polymer architecture and the thermal and crystalline behaviour. © 2019 Society of Chemical Industry     

固体碳直接还原钢铁厂含锌固废的理论与实践

 钢铁厂内的含锌固废数量巨大，同时富含铁、碳等元素，是可循环再利用的二次资源。通过固体碳直接还原ZnO和FeO的热力学分析，发现在非标准状态下，ZnO的还原条件要优于FeO。为此，在实验室条件下设计了含锌固废在不同温度和时间下的还原试验，发现在还原温度为1 423 K、还原时间为15 min以上时，脱锌率可达到90%，而铁的金属化率需要在1 573 K时才能接近90%；在还原温度低于1 423 K时，还原时间对脱锌率的影响较大；在还原温度高于1 473 K时，还原温度对脱锌率影响较小，同时脱锌率可达到95%。这些结果对国内当前处理含锌固废主要工艺(回转窑、转底炉)的操作制度设置具有重要的参考价值，也为如何选择合理的工艺路线，以低投入、低运营成本实现含锌固废的再利用提供了理论依据。